D*lce si oscam

**fery21** · 12-03-10, 10:11

Decarcati oscam de pe server + config-ul

apoi: var/tubox/config editati fisierele:

-oscam.conf

Code:

[global]
nice = -1
WaitForCards = 1
[monitor]
port = 988
aulow = 120
monlevel = 0
[newcamd]
key = 0102030405060708091011121314
port = 22000@092f:000000

-oscam.server

Code:

[reader]
Label = Dolce (39E)
Protocol = Intern
Detect = CD
Device = dev/sci0 #sau dev/tts0 ptr phonix
group = 1
#emmcache = 1,3,2
#mhz = 525
CAID = 092f
BoxID = 123abc 
#savenano = all
Customspeed = 0
EMMCache = 1,3,2
Fallback = 0

-oscam.user

Code:

[account]
user = user
pwd = passwd
group = 1
uniq = 1
caid = 092f
ident = 092f:000000
AU = Dolce (39E)
monlevel = 0

Copiati linia N in CCcam.cfg

Code:

N: 127.0.0.1 22000 user passwd 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256

**zappa** · 12-03-10, 10:18

Intrebare: daca dulcele merge bine direct in cccam, atunci de ce mai este nevoie de oscam?

**fery21** · 12-03-10, 10:21

Adevarat dar eu vreau cadul direct si nu in hop1 in cazul meu avand 3 receptoare cu linie n ecm max 200 zic e mult mai rapid decat CCcam

**potty** · 23-03-10, 09:12

nu am reusit sa pornesc cardul cu aceste setari ..

**badeaghio** · 05-06-10, 16:07

daca acum folosesc cccam 2.1.3, si cardul de dolce il citesc cu cccam-ul, dupa ce pun oscam, ce modificari trebuie facute in cccam.cfg?

mai ramane acolo boxkey-ul?

**JBTC** · 05-06-10, 16:59

Adaugi linia N. poate sa ramana boxkey in cccam.cfg pt ca oricum reader-ul va fi oscam

uite setarile mele:

in ccam.cfg adaugi N (va fi in hop 0)
---------

Code:

N: 127.0.0.1 50000 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256

sau C (va fi in hop1)

Code:

C: 127.0.0.1 12001 user pass no

oscam.conf
-----------

Code:

[global]

Nice = -1
saveinithistory = 1
LogFile = stdout
logfile = /var/log/oscam.log
usrfile = /var/log/oscamuser.log
maxlogsize =10
pidfile = /var/run/oscam.pid
ClientTimeout = 5
CacheDelay = 120

[monitor]
Port = 1000
NoCrypt = 192.168.1.1-192.168.1.250
AULow = 120
MonLevel = 2

[webif]
httpport = 8888
httpuser = userwebif
httppwd = passwebif
httprefresh = 10
httpallowed = 1.0.0.1-254.254.254.254

[newcamd]
Key = 0102030405060708091011121314
Port = 50000@092F:0000

[cccam]
port = 12001
reshare = 2
version = 2.1.3
build = 213

oscam.server
-------------

Code:

[reader]
AU = 1
Enable = 1
label = Dolce (39E)
Label = Slot0
Protocol = internal
detect = cd
device = /dev/sci0
mhz = 500
Fallback = 0
Group = 1
CAID = 092f
ident = 092f:000000
boxid = XXXXXXXX
EMMCache = 1,1,2
pincode = 0000

oscam.user
-----------

Code:

[account]
User = user
Pwd = pass
monlevel = 1
AU = 1
Uniq = 1
Group = 1

**badeaghio** · 10-06-10, 13:36

OK, am reusit sa pornesc CCCam 2.1.3 si Oscam. problema e: nu imi mai apare cardul la Entitlements, apare doar

127.0.0.1:50000 |00d 00:02:00|newcamd | | | 1 |remote 092f:000000 6(0)

la sectiunea Servers.

se pare ca nu decodeaza.
aseara am mutat antena pe 39*est, si pentru mine (lolcal) decoda (doar cu cccam 2.1.3), in schimb, ecm-uri primite de la clienti nu decoda.

macar stiu acum ca am boxkey-ul bun

Ce sa-i fac ca sa decodeze si pt clienti?

**JBTC** · 10-06-10, 13:39

le dai linii N sau C dar trebuie sa-i adaugi in oscam.user

ex

oscam.user

Code:

[account]
User = user
Pwd = pass
monlevel = 1
AU = 1
Uniq = 1
Group = 1

[account]
User = user2
Pwd = pass2
monlevel = 0
AU = 0
Uniq = 1
Group = 1

entitlements iti apare in webif al oscam acum pt ca oscam este reader

**badeaghio** · 10-06-10, 14:47

deci trebuie sa retrimit linii N la toata lumea? deci la fiecare peer sa am linie F in cccam.cfg si user+pass in oscam.user?

eu tot cred ca nu decodeaza, la servers, la cccam webif apare: remote 092f:000000 95(0)

numai un client se pare ca foloseste cardul acum, dar poate nu am eu pachetul activ pentru canalul la care priveste el. cred, sper

nu gasesc fisierul de log. nu e in /var/log

---------- Post added at 13:47 ---------- Previous post was at 13:09 ----------

asta e din log:

-------------------------------------------------------------------------------
>> OSCam << cardserver started at Thu Jun 10 13:31:19 2010
-------------------------------------------------------------------------------
2010/06/10 13:31:19 448 s version=0.99.4svn, build #2330, system=powerpc-tuxbox-linux, nice=-1
2010/06/10 13:31:19 448 s max. clients=29, client max. idle=120 sec
2010/06/10 13:31:19 448 s max. logsize=10 Kb
2010/06/10 13:31:19 448 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2010/06/10 13:31:19 448 s shared memory initialized (size=492830, fd=5)
2010/06/10 13:31:19 448 s anti cascading disabled
2010/06/10 13:31:19 448 s dvbapi disabled

imagini: http://img17.imageshack.us/gal.php?g=usersh.png

**fery21** · 10-06-10, 15:37

Nu ai nevoie sa dai linie N ficcarui per din CCcam (desi atentie mare cu linile N!!)

in oscam.config nu ai drirectionat bine fisierul log
/var/tuxbox/config/ cred ca aici e celmai bine sa il pui

**fery21** · 10-06-10, 20:15

Explicati legate de PM

Gasiti aici
Ori ce Linie N creata poate fii multiplicata! asta e atentia controlul il aveti un emulator

**expression** · 11-06-10, 18:58

In configuratia de mai sus oscam+CCcam se mai face AU la card?

**badeaghio** · 12-06-10, 08:52

cum overclockez cardul in Oscam? schimb la oscam.server mhz=500 cu ce?
nu merge cardul cum trebuie pentru clienti, adica din 250 de ecm-uri primite, doar 10 sunt rezolvate....si ma gandesc ca poate e frecventa la card prea mica.

**SuperSonic** · 12-06-10, 11:12

Eu il am in cccam trecut la 600 si merge bine, incearca sa pui asa.

**fery21** · 12-06-10, 11:26

Merge bine cu Mhz=657

---------- Post added at 10:26 ---------- Previous post was at 10:17 ----------

[account]
User = user
Pwd = pass
monlevel = 1
AU = 1 acesta face au la userul respectiv
Uniq = 1
Group = 1

[account]
User = user2
Pwd = pass2
monlevel = 0
AU = 0 dezactivat au ptr acest user
Uniq = 1
Group = 1

Thread: D*lce si oscam

Thread Tools

Display

D*lce si oscam

...

AU

Posting Permissions