Probleme rescriere imagine Spark

**stargate** · 01-01-12, 21:02

Code:

U-Boot 1.3.1 (Mar 16 2011 - 11:42:45) - stm23_0043 - YW 1.0.019 Rel P1

DRAM:  128 MiB
NOR:     8 MiB
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
IdentID : 09 00 0a 00 00 4b b0
Hit ESC to stop autoboot:  0

Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000

 ** Bad Magic Number 0xffffffff **
## Booting image at 80000000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...

O eroare de genul celei de mai sus am primit atunci cand am instalat prima data imaginea lui @pinky care este format YAFFS2 si nu cum sunt celelalte imagini sunt JFFS2 fapt ce duce la o schimbare de bootargs . Eroarea s-a rezolvat la acel moment cu ajutorul lui @zildan , apoi am invatat cum se face o instalare in format YAFFS2 si apoi trecerea din nou la JFFS2 fara sa am erori . Ciudat este ca Spark mergea rescris fara probleme ... problema era la Enigma . Problema la tine este imposibilitatea de a iesi manual din autoboot fie cand incerci pornirea cu butonul OK apasat fie pe seriala ... si daca cablul serial este ok atunci a intervenit o problema grava si uboot nu mai comunica cu panoul frontal si nici pe seriala .

**proteus** · 01-01-12, 23:38

Originally Posted by MaximusFBI

La probleme anormale solutii anormale.

Maestre, m-ai salvat! Paranormal, nu alta. Am fost plecat cateva ore, l-am scos din priza si am scos toate cablurile din el. Can m-am intors, a mers din prima sa intru in Emergency boot.

Acum pare totul OK, am instalat ultimul Enigma RSP si acum il configurez.

E de antologie toata faza....

**stargate** · 02-01-12, 10:27

Bine ca ai rezolvat ... probabil nu il lasai deloc dupa ce il opreai din intrerupatorul din spate , in general este bine sa fie lasat 1-2 minute pentru a se descarca complet toti condesatorii din aparat .

Spor la teste

**proteus** · 02-01-12, 13:06

OK, e de retinut pentru viitor. Multumiri inca o data pentru efort.

**iannys** · 29-07-13, 22:04

Buna seara la toata lumea.Aceeasi problema o intimpin si eu ca si Proteus dar ca la mine nu vrea sa-si revina singur nici in ruptul capului ramine tot la load.Am tot incercat cu diferite marci de stickuri si cu cisco tftp si nu vrea deloc.Ce ma sfatuiti sa m-ai incerc?As incerca si cu hyper terminal cu u-boot.bin dar nu-l gasesc.Daca ati putea posta un link de unde sa-l descarc as incerca.

**gauloises** · 30-07-13, 14:56

Trimite-l la garantie.
Aaa am patit si eu si nicicum nu l-am putut resuscita

Sent from my GT-I9100 using Tapatalk 4 Beta

**zildan** · 30-07-13, 22:23

Daca ai cablu serial vezi mai concret care e buba.
Aparatul poate fi resuscitat!

**iannys** · 30-07-13, 22:27

Da am cablu cu care rescriu imaginea la dreambox.Sper ca este ok. Da-mi niste sfaturi ideii detalii despre cu as putea sa-l readuc la viata pe extraterestru

**zildan** · 30-07-13, 23:14

Conectezi cablu serial, setezi seriala cu putty 115200 8 N 1 apoi vezi pe terminal meniul.

**iannys** · 31-07-13, 21:13

Timed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/0(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCC
Ce anume ar trebui sa vad ?
Doar asta imi arata putty.

**zildan** · 01-08-13, 21:52

Clar nu !
Porneste seriala inainte de a da power on.

**iannys** · 01-08-13, 22:21

2˛ b°
c 6łm-đ
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCC
Asta arata acum.

**zildan** · 02-08-13, 09:33

Ca sa recapitulam .... daca pornesti tinand apasat OK se schimba ceva in logul asta?

**iannys** · 02-08-13, 23:48

Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
Warning: MAC addresses don't match:
HW MAC address: FF:FF:FF:FF:FF:FF
"ethaddr" value: 00:80:E1:12:06:38
Using MAC Address 00:80:E1:12:06:38
*** ERROR: `ethaddr' not set
Asta arata daca tin butonul ok apasat.

---------- Post added at 23:48 ---------- Previous post was at 23:34 ----------

<ŰŤľ[ý˙
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CC
Asa arata cind incerc sa-l pornesc pe spark

ŰDŰ}żíý
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_enigma2
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCC
Asta arata cind incerc pe enigma 2

**iannys** · 02-08-13, 23:59

Ďýë˝˙
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCC

Asta arata cind incerc pe spark

ß˝ý÷
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_enigma2
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCC

Asta pe enigma 2

Thread: Probleme rescriere imagine Spark

Thread Tools

Display