Un extraterestru mort - apare doar ceasul 00:00

**pop1234** · 14-03-14, 16:10

hello

i have problem boot

no run in spark and enigma2

spark : ok+power+up+ok = display err

enigma2 : ok+power+down+ok = display err

Code:

Board: STx7111-Mboard (MB618)  [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM:  128 MiB
NOR:     8 MiB
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
IdentID : 09 00 07 00 00 80 51 

Hit ESC to stop autoboot:  5  4  3  2  1  0 
## Booting image at a0080000 ...
   Image Name:   Kernel-Ramdisk-Image
   Image Type:   SuperH Linux Multi-File Image (gzip compressed)
   Data Size:    5867343 Bytes =   5.6 MiB
   Load Address: 80800000
   Entry Point:  80801000
   Contents:
   Image 0:  2970211 Bytes =   2.8 MiB
   Image 1:  2897119 Bytes =   2.8 MiB
   Verifying Checksum ... OK
   Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 907008051
   Loading Ramdisk to 80d3c000, length 002c34df ... OK

Starting kernel      nwhwconf=device:eth0,hwaddr:24:00:07:00:80:51 Manufacture=Spark-Project STB_ID=09:00:07:00:00:80:51 - 0x0053d000 - 2897119 ...

and

menu + power

Code:

Board: STx7111-Mboard (MB618)  [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

RAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 80 51
Hit ESC to stop autoboot: 5
MB618> printenv
bootdelay=5
baudrate=115200
bootcmd=bootm 0xa0080000
boot_system=spark
kernel_name=spark/mImage
userfs_len=17800000
tftp_kernel_name=mImage
tftp_userfs_name=userfsub.img
userfs_name=spark/userfsub.img
stdin=serial
stdout=serial
stderr=serial

Environment size: 243/131068 bytes
MB618>

**ionut_pit** · 14-03-14, 19:53

try recovery - method no. 3 from this pdf "howto_ENG_Upgrade_Spark_on_Amiko_Alien_Series_v130610a.pdf",
you can download it from here :http://www.amikostb.com/?q=product&id=8

**pop1234** · 14-03-14, 20:56

ionut_pit

VFD/LED display err

**ionut_pit** · 14-03-14, 21:44

the stick must be FAT 32 format and contain only userfsub.img and mImage in a folder called "spark".
Also you can try with another USB stick (maximum 4Gb capacity)

**pop1234** · 14-03-14, 22:04

i tested with ADATA 4GB & Verbatim 4GB err

**zildan** · 14-03-14, 22:21

Your boot environment is corupted.
You have to rewrite all boot environment parameters.

**pop1234** · 14-03-14, 23:09

zildan

explain to me more

---------- Post added at 22:09 ---------- Previous post was at 22:04 ----------

please help me
i want to solve this problem

**zildan** · 15-03-14, 22:48

Write bootargs:

Code:

Connect the receiver to your PC with Null-Modem (Cross-Wired RS232) cable

Open PuTTY

Select your COM1 port, set the baud rate to 115200 and open the connection

Turn the receiver ON

When you see the 'PK7105' prompt, copy the following command without the quotes ("") and press ENTER:

Step:1 

"set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:06:37:04:15:00
ip=192.168.40.83:192.168.40.19:192.168.40.1:255.25 5.0.0:lh:eth0ff
stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=6000"

When you see the 'PK7105' prompt again, copy the following command without the quotes ("") and press ENTER:

Step:2

"nboot.i 0x80000000 0 0x00100000 ;bootm 0x80000000"

The receiver should boot to SPARK

after booting to spark go to (SPARK) icon and then update,

when the updating is finished repeat the stem:1 and step:2 then your box should or will boot to spark image.


Upgrade the receiver to the "spark_1.2.54 Europe" version (This is
important!)

OR Write Boot-loader:

How to Upgrade Uboot by RS232

Preparation:
1. Open [HyperTerminal] and set default parameters
Symbol rate: [1152000]
Data bits: [8]
Parity: [None]
Stop Bits: [1]
Data Flow Control: [None]
2. Select [Transfer/File Transfer] Option
3. Select [u-boot.bin] and use [Ymodem] Option, send file
Upgrade Step:
1. Keep Pressing [OK] Button in Front Panel, then power on STB.
2. After 5 seconds you will see [Forc] in LED, release [OK] button and press [Left]
Button.
3. If everything is ok, in STB you will see [LOAD] shinning in LED.[COLOR="Gray"]

**pop1234** · 18-03-14, 11:50

Thank you

I've been solving the problem

That way

hyper terminal

Code:

### for GM990Reloaded ###################################
ac off
ac on + hold menu-button
now you can press in your terminalprogram "3"-exit 
and you are on prompt:
mb618>
#########################################################
### fix args by comcable ################################
#########################################################
setenv ethaddr '00:80:E1:12:06:38'
setenv bootdelay 3
setenv baudrate 115200
setenv board mb618
setenv monitor_base '0xA0000000'
setenv monitor_len '0x00080000'
setenv monitor_sec '0xa0000000    0xa007ffff'
setenv load_addr '0x80000000'
setenv unprot 'protect off $monitor_sec'
setenv update 'protect off $monitor_sec;erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on $monitor_sec'
setenv HOSTNAME LINUX7109
setenv ipaddr '192.168.40.63'
setenv netmask '255.255.255.0'
setenv gatewayip '192.168.3.1'
setenv serverip '192.168.40.19'
setenv kernel_base_spark '0xa0080000 '
setenv kernel_base_enigma2 '0x18000000'
setenv kernel_sec 'a0080000 a077ffff '
setenv kernel_len '0x00700000'
setenv update_kernel 'protect off  a0080000 a077ffff ;erase  a0080000 a077ffff ;cp.b 0x80000000 0xa0080000  0x00700000 ;protect on  a0080000 a077ffff '
setenv rootfs_base '0xa0800000'
setenv rootfs_sec 'a0800000 a1ffffff'
setenv menucmd update
setenv tftp_kernel_name_spark mImage
setenv tftp_kernel_name_enigma2 uImage
setenv tftp_userfs_name_spark 'userfsub.img'
setenv tftp_userfs_name_enigma2 'e2jffs2.img'
setenv kernel_name_spark 'spark/mImage'
setenv kernel_name_enigma2 'enigma2/uImage'
setenv userfs_name_spark 'spark/userfsub.img'
setenv userfs_name_enigma2 'enigma2/e2jffs2.img'
setenv userfs_base_spark 800000
setenv userfs_base_enigma2 18800000
setenv userfs_len_spark 17800000
setenv userfs_len_enigma2 7700000
setenv kernelnfspath '192.168.40.19:/opt/target'
setenv rootfs_name UserFS
setenv rootfsnfspath '192.168.40.19:/home/d22cj/workspace/target'
setenv uboot_name 'u-boot.bin'
setenv ubootnfspath '192.168.40.19:/home/d22cj/workspace/target'
setenv bootfromnfs 'nfs a4000000 $kernelnfspath/$kernel_name;bootm a4000000'


setenv bootargs_nfs 'console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 stmmaceth=msglvl:0,phyaddr:1:watchdog:5000 root=/dev/nfs nfsroot=192.168.40.19:/opt/target,nfsvers=2,rsize=4096,wsize=8192,tcp rw ip=192.168.40.61:192.168.40.19:192.168.3.1:255.255.0.0:LINUX7109:eth0:off bigphysarea=4000'


setenv bootargs_flash 'console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000'


setenv bootargs_spark 'console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000'


setenv magic_version '1.7'
setenv filesize '203CA88'
setenv fuseburned true
setenv stdin serial
setenv stdout serial
setenv stderr serial


setenv bootargs_enigma2 'console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000'


setenv bootargs 'console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000'


setenv bootcmd bootm  '0xa0080000'
setenv boot_system spark
setenv userfs_base '800000'
setenv userfs_len '17800000'
setenv kernel_base '0xa0080000 '
setenv kernel_name 'spark/mImage'
setenv userfs_name 'spark/userfsub.img'
setenv tftp_kernel_name mImage
setenv tftp_userfs_name 'userfsub.img'


### before doing saveenv check via "print" if all correct!!! ####
saveenv


#############################################
### end #####################################


now you turn ac off
ac on and orig should bootup again
if orig not booting you must flash rescue-pack1.2.09 again from here(watch readme how to flash):
http://kathif.vs120005.hl-users.com/filebase_entry.php?entryid=374&sid=

**ionut_pit** · 21-03-14, 22:00

Originally Posted by ionut_pit

Satutare tuturor,

@k-mel puteai sa rezolvi usor folosind o interfata FT2232H mini module.

Exemple avem mai jos :

si

Am gasit aceasta interfata pe mai multe site-uri in jur de 27$
Problema e costul de livrare cam mare aprox. 15$
Poate stiti voi undeva mai ieftin...?

Acum 2 saptamani am reusit sa readuc la viata extraterestrul meu cu ceas digital

Am folosit o interfata FT2232HL mini module adusa din China.
Conexiunile trebuiesc facute de la JTAG la portul USB al PC-ului (folosind un cablu USB mini ), de la portul serial al PC-ului (COM 1) la portul RS232 al receptorului (folosind un cablu serial nullmodem), de la pinii JTAG-ului (AD0.....AD7 si GND) la cei ai receptorului (GND,TCK,TDI,TDO,TMS,nTRST,nSRST,nASERBK,TRIGOUT) si de la pinul de 3,3 volti al JTAG-ului la pinul VIO. Ceva documentatie in engleza avem aici :http://www.4shared.com/get/fJz34RMk/...n_argus_p.html
Cine vrea sa incerce dispun de toata informatia necesara.
Atasat am pus poze din timpul operatiunii

**zildan** · 21-03-14, 22:51

jtag-flash for edision argus pingulux receiver format PDF

**k-mel** · 25-10-14, 01:52

Un an si jumatate...

Atat a fost in moarte clinica extraterestrul meu. L-am inviat in seara asta. Mi-am luat statie de lipit cu aer cald acum cateva zile si am putut sa ma ocup de el pe indelete, sa-i indrept cele doua trasee de pe placa pe care le-am exfoliat. Dupa lungi insistente, a luat-o. In sfarsit am pe el spark-ul original si nu mai am chef in seara asta sa caut cum se mai configureaza cccam-ul, cum se instaleaza enigma, etc. Si, ca sa fie treaba completa, in dimineata asta am dat deja comanda de interfata jtag cu chip ft2232; cred ca la ora asta pleaca din China...

In fine, e aproape doua noaptea si mi-e si mie somn. Am vrut doar sa stiti si voi ca tot topicul asta de 3 pagini n-a fost in zadar. Multumiri tuturor!

**ionut_pit** · 25-10-14, 22:09

Felicitari! App am observat ca eroarea cu SW illegal revine si asta fara sa-i mai fac vreun update, pur si simplu doar pt ca porneste cu reteaua conectata.L-am rescris de 3 ori pana acum.

**zildan** · 26-10-14, 01:15

Fii mai explicit, cred ca gresesti ceva .

**ionut_pit** · 26-10-14, 12:32

Acum nu-l mai am, mi-am luat 8250+.Dar ca ideee sa-ti spun ce patisem.I-am rescris boot-ul prima data folosind interfata ft2232h, i-am pus ultimul soft original, a mers cateva luni fara probleme apoi fara sa-i fac update sau altceva a reaparut problema cu SW ilegal.L-am rescris din nou, am pus ultimul soft si l-am pornit cu reteaua in el.Dupa 1 minut de functionare normala a reaparut Sw ilegal si apoi ceas 00:00.L-am rescris iar, am incercat toate variantele de soft originale si vechi si noi si la fel se comporta cu toate.Mi-am dat seama ca problema este din retea, de acolo probabil isi facea update automat si il detecta apoi cu SW ilegal.Am continuat sa-l folosesc dar nu-l mai porneam cu reteaua in spate, o puneam apoi dupa 2-3 minute de la pornire si mergea fara probleme.Am continuat apoi sa-l folosesc pe Spark.Am incercat si Enigma ca sa nu mai am probleme vreodata insa mi se parea o varianta prea greoaie in comparatie cu Spark-ul.

Thread: Un extraterestru mort - apare doar ceasul 00:00

Thread Tools

Display

Posting Permissions