K1 plus dvb-s2 / t2 (4K)

[zildan]

Error in /udisk/wetekplay2-masterv1.4-ota-k1-plus-by-belaid38-signed.zip
(status 7)

[MAHDI-DZ]

updated wetekplay2-masterv1.4-ota-k1-plus

http://myreader.toile-libre.org/uplo...cacba6af59.pdf

[zildan]

I know the procedure this is the result.

[MAHDI-DZ]

KI_PLUS_DTV-ota-20161107.195841.V1031P3（PowerVU)








---------- Post added at 13:55 ---------- Previous post was at 13:47 ----------

I know the procedure this is the result.

@zildan
- 1 used sdcard
http://myreader.toile-libre.org/uplo...cacba6af59.pdf

If it stays the same problem Try
- 2 add original file k1 recovery.img and factory_update_param.aml in softw.zip

[zildan]

PowerVU din 07.11.2016

This version is the first version of PowerVU test software, this update is as follows:

1, increase PowerVU function.
2, to optimize the SD program display.

If you are using USB / TF card upgrade, select the Erase Data Partition and Erase Media Partition before upgrading.

KI-PLUS S2+T2 USB/TF ZIP FILES
https://yadi.sk/d/abmq0HP_yGVH5
or
https://mega.nz/#!SkNAja4A!wU7EHv_FG...iRj40_s2_3r7Vw

KI-PLUS S2+T2 IMG FILES
https://yadi.sk/d/9q4Oa_0ryGD5Z
or
https://mega.nz/#!ftU2yDrR!EreJTYdza...Sq1vN7VZvIkHXI

---------- Post added at 16:43 ---------- Previous post was at 15:41 ----------

; ===========================================
# POWERVU Key credit to engineer khan15 #
; ===========================================

## An example format
## -> P IDENT Even odd KEY
## -> IDENT = satellite angle + satellite frequency
## -> If the satellite 66E is 660 degrees, it is the hexadecimal 294, make up four, the front zero is 0294
## -> Suppose the satellite 138E is 1380 degrees
## -> Assuming the frequency is 3845, its hexadecimal is F05, make up four, in front of zero is 0F05
## -> so together is: 02940F05

Am reusit sa traduc explicatiile din chineza.
Incerc sa introduc ceva key locale .

[zildan]

Page 1
KI PLUS S2 PowerVU KEY Instructions for use
1. Enter the digital TV, press the MENU button to display the digital TV menu, select the "Setup" menu, press the OK button to enter.
2. In the installation setup interface, press the "1" key on the remote control 6 times to enter the Smart Data management interface, select PowerVU
Function Press OK to enter.
3. PowerVU key manually add support to add USB and bulk import / export in two ways.
A. Press the red key on the remote control to manually add the PowerVU key.
Page 2
Enter the appropriate parameters, press the OK key to complete the PowerVU key to add.
B. USB bulk import, export PowerVU key.
The file name of the PowerVU key is SoftCam.Key.
Copy the SoftCam.Key file into the USB device, and then access the KI-PLUS box USB interface, in the PowerVU menu
Interface Press the yellow button on the remote control to import the PowerVU KEY in batches.
Enter the satellite parameters
Enter the corresponding KEY
Press on the remote control
Press to enter letters
Page 3
Press the blue key on the remote control to back up the PowerVU key to a USB device.
After the backup USB device will be connected to the computer will see a softcam.key name of the file.
Open the file and display the file format of the KI-PLUS PowerVU key. (The following figure)
Note: If you use other devices softcam.key KI plus file into the box, because the format is not prepared
, There will be satellite after the introduction of the angle and TP display is 0, if you want to show the actual satellite parameters, you can
First import the file into the box, and then back up to KI PLUS format, and then manually modify the satellite on the computer and the angle
TP, and then through the USB into the box. (If you do not want to modify, the use of the function has no effect)

---------- Post added at 19:19 ---------- Previous post was at 19:02 ----------

http://masrawysatlinux.com/t11283.html

Confirm ca merge, dar sacadeaza.

[konstantine]

Și pe alte receptoare sacadeaza cand merge in paralel emu cu sharingu'.Eu inchid conexiunea la net din receptor si funcționează ok.

[zildan]

PV 0167300F 00 xxxxxxxxxxxxxx 001 0 W 12303 V
PV 0167300F 01 xxxxxxxxxxxxxx 001 0 W 12303 V

key from previous lynk
Discovery-Networks
Thor1°W- 12303-V-27500

[zildan]

Am verificat si merge cu key de forma :

PV 0000000 00 xxxxxxxxxxxxxx 001 0 W 12303 V
PV 0000000 01 xxxxxxxxxxxxxx 001 0 W 12303 V

Daca linia contine satelitul si transponderul nu mai necesita ident.
Din pacate doar "deschide" nu merge fluent, sacadeaza sau se agata.
E totusi un pas inainte!

[zildan]

Azi am facut mai multe teste cu softul din 07.11.2016 si am descoperit ca s-a rezolvat problema cu USALS, in sensul ca nu mai e necesara corectarea coordonatelor sa mute corect antena.
Nu cred insa ca s-a rezolvat si problema cu trecerea prin meniul de motor la intrarea in soft .

[zildan]

Se pare ca muta antena fara sa mai treci prin meniul motor.
Scanez de cateva ore satelitii fara "blind", asta va recomand si voua.
Cand scanezi cu blind mai apar prostii.

[zildan]

S-a rezolvat si problema cu pachetul DVB-T2 al SNR.

[TinjalA]

O parere de la baieti
E mai bun k1 plus sau ferguson ariva 4k combo?
Multumesc o zi buna

Inviato dal mio GRACE utilizzando Tapatalk

[MihaiP]

Mda ! le-a cam trebuit ceva vreme ...

[marcghi]

Are ceva sanse pentru DVB-C ?