Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 5 of 5

Thread: How to cas2

  1. #1
    O zi frumoasa! Snow's Avatar
    Join Date
    05 Jan 2007
    Posts
    3,368
    Mentioned
    0 Post(s)
    Rep Power
    86

    Default How to cas2

    programare cam cu cas2:

    se introduce cam-ul in cas



    se deschide cas studio


    selectati cam module apoi cam-ul dorit


    dati connect apoi erase all si asteptati pana se termina stergera flash-ului


    apoi selectati open file si incarcati fisierul dorit, apoi click pe write si asteptati

    cand s-a terminat scrierea, dati exit, scoateti camul din programator si fuga cu el in receiver.
    Vizionare placuta!

    ps: daca dupa erase va apar niste erori de genul "error in blank 3", se va repeta procedura de erase, apoi incarcati softul dorit
    Last edited by Snow; 31-05-08 at 11:22.





  2. #2
    Member Beginner
    Join Date
    06 Dec 2007
    Posts
    11
    Mentioned
    0 Post(s)
    Rep Power
    0

    Default Re: How to cas2

    Buna seara se poate reprograma un cam Aston seca in cripto sau viacces multumesc anticipat .
    Last edited by Snow; 08-06-08 at 00:46. Reason: qoute

  3. #3
    O zi frumoasa! Snow's Avatar
    Join Date
    05 Jan 2007
    Posts
    3,368
    Mentioned
    0 Post(s)
    Rep Power
    86

    Default Re: How to cas2

    nu stiu sigur, dar ma interesez pentru tine





  4. #4
    O zi frumoasa! Snow's Avatar
    Join Date
    05 Jan 2007
    Posts
    3,368
    Mentioned
    0 Post(s)
    Rep Power
    86

    Default Re: How to cas2

    m-am interesat dar raspunsul nu este unul pozitiv, imi pare rau.





  5. #5
    O zi frumoasa! Snow's Avatar
    Join Date
    05 Jan 2007
    Posts
    3,368
    Mentioned
    0 Post(s)
    Rep Power
    86

    Default Re: How to cas2

    uite si o varianta promitatoare

    This is a quick help file to run through upgrading your Aston/Cryptoworks CAM using Windows 95/98 and PCMCIA.
    ATT: Do not use on Aston 1.04 CAM only on 1.00 or 1.03 versions.

    Perfrom this at your own risk.. I had no problems, but it could fry your cam...

    Files:
    load.exe Program to load .bin file to CAM
    aston95.inf driver file for Aston CAM under win95
    aston98.inf driver file for Aston CAM under win98
    cryptoworks95.inf driver file for Cryptoworks CAM under win95
    cryptoworks98.inf driver file for Cryptoworks CAM under win98
    aston103.bin Aston CAM v1.03 update file
    cw112.bin Cryptoworks CAM v1.12 update file
    cw114.bin Cryptoworks CAM v1.14 update file
    UpgradeReadme.txt This file


    Delete the .inf files you don't need, for example leave aston98.inf if using win98 and updating an aston Cam.

    Boot your PC into windows insert your cam and when prompted for the driver point it to the directory
    with the .inf file. If prompted to restart do so.

    Ensure that in device manager you have a Smart Card section with the CAM with no error symbols.
    If you have errors you may need to adjust the resource settings.

    Only proceed if you are sure of the above.

    Run a command prompt change (MS-DOS Prompt) to the temp directory and enter below on one line.

    load aston103.bin (for update to aston 1.03)
    or
    load cw114.bin (for update to Cryptoworks CAM v1.14)
    and so on......

    It should then cycle through a counter which is programming your cam.

    Do not interupt it, breath too heavley etc when it is programming as this will fry your cam.

    When it is finished it will tell you.. Press Q to quit.

    You can remove your CAM and there you go you have a an updated CAM :-)

    Hope this helps you..

    Regards,

    thanks to GionniQ

    si vezi poate te ajuta si asta http://www.lefdata.com/satellite/cam/ci.html





Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •