Antentie configurarea este doar pentru ipbox 900!!!!
Cu multumiri lui Zildan pentru ajutorul oferit.
in cazul meu portul pentru newcs este 10110 linia C e de genul<?xml version="1.0"?>
<!--
For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around )
-->
<newCSconfig>
<globals>
<listening-ip>127.0.0.1</listening-ip>
</globals>
<readers name="Card Readers">
<device>
<name>Phoenix Interface</name>
<type>phoenix</type>
<mhz>357</mhz>
<node>/dev/ttyUSB0</node>
<parity>even</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10110</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
</readers>
<radegastserver>
<!-- valid value for enable are:
0,1 - Enable or Disable radegast server. -->
<enabled>no</enabled>
<!-- valid value for port are:
0,65535 - Which port to listen for incomming connections. -->
<port>10001</port>
<!-- valid value for allow are:
ALL - Not active yet. -->
<allow>
<hostname>127.0.0.1</hostname>
</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>verbose</level>
<type>init</type>
<output>all</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>bla</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<allow>lower</allow> <!--Use this just when you want give free just some readers to your Users -->
<allow>upper</allow> <!--Use this just when you want give free just some readers to your Users -->
</user>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
</user>
</newcamdserver>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>newcs</name>
<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>newcs</password>
<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
</newCSconfig>
C: { 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 0B000000:0B000000;}
unde { 0B000000:0B000000;} este id-ul cardului meu
1200.list se redenumeste in 10110 list si se scrie linia SF: { 0000 } desi cel mai bine e sa scrieti sid-ul la fiecare canal in parte in aceasta lista
va atasez mai jos si fisierul newcs.xml
Cum verific daca ipbox comunica cu interfata Phoenix?
cu gbox control center ultima versiune, sau dai pe canalul care stii ca ar trebui sa-l deschida carul tau si apesi tasta galbena
daca scrie local, trage de pe ea, daca scrie network atunci....
Am pus phoenix cu mgcamd+newcs+rs232 si a mers (card TVR).
Am trecut la mbox+newcs+rs232 si nu merge sa citesc local cardul.
La debug imi apare:
*************** New Start 11.10.2008 19:49:19 ***************
[19:49:19] STAPI INIT ... OK
[19:49:19] ExYuSAT Team http://www.exyusat.com , http://mbox.exyusat.com/index.php
[19:49:19] Starting MBOX version 0.4 BETA (build 0012) coded by The_Ripper
[19:49:19] This program is for educational & informational purposes only!!
[19:49:19] Donation to project: http://mbox.exyusat.com/donate.htm
[19:49:19] ===> Local Mode <===
[19:49:19] Reading cwshare.cfg ...
[19:49:19] Trying to get online,please wait ...
[19:49:19] Total 1 newcamd server(s) to connect
[19:49:19] Creating ecm parser thread ...OK
[19:49:19] Creating timer thread ...OK
[19:49:19] Creating newcamd worker thread ...OK
[19:49:19]
[19:49:19] ReReading pmt.tmp
[19:49:19] ==================================================================
[19:49:19] ECM: CA ID: 0x1702 Nagravision -> CA PID: 0x1009
[19:49:19] ECM: CA ID: 0x1722 Nagravision -> CA PID: 0x1009
[19:49:19] ECM: CA ID: 0x1830 Nagravision -> CA PID: 0x1948
[19:49:19] ECM: CA ID: 0x1833 Nagravision -> CA PID: 0x1848
[19:49:19] ECM: CA ID: 0x1834 Nagravision -> CA PID: 0x1C48
[19:49:19] ECM: CA ID: 0x09C4 NDS -> CA PID: 0x1B48
[19:49:19] ECM: CA ID: 0x1801 Nagravision -> CA PID: 0x1648
[19:49:19]
La restart a plecat pe premiere.
==================================================================
[19:49:19] [newcamd] Trying to connect to newcamd server (127.0.0.1:10110)
[19:49:19] [newcamd] Connected to (127.0.0.1:10110) ...
[19:49:19] [newcamd] Got card with CaID 0x0500 and 3 number(s) of ProvID (127.0.0.1:10110)
[19:49:19] [newcamd] Card: CaID 0x0500 ProvID: 0xFFF720 (127.0.0.1:10110)
[19:49:19] [newcamd] Card: CaID 0x0500 ProvID: 0x025900 (127.0.0.1:10110)
[19:49:19] [newcamd] Card: CaID 0x0500 ProvID: 0x025910 (127.0.0.1:10110)
[19:49:19] [newcamd] Creating newcamd worker thread for (127.0.0.1:10110) ...
OK
[19:49:38]
[19:49:38] ReReading pmt.tmp
[19:49:43]
[19:49:43] ReReading pmt.tmp
[19:49:43] ==================================================================
[19:49:43] *ECM: CA ID: 0x0500 Viaccess (00000000) -> CA PID: 0x0032
[19:49:43] *ECM: CA ID: 0x0500 Viaccess (00000000) -> CA PID: 0x0033
[19:49:43] *ECM: CA ID: 0x0500 Viaccess (00000000) -> CA PID: 0x0034
[19:49:43] ==================================================================
[19:49:43] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:49:43] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:49:43] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:49:43] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:49:43] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:49:43] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:49:51] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:49:51] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:49:51] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:49:51] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:49:51] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:49:51] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:01] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:01] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:01] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:01] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:01] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:01] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:11] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:11] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:11] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:11] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:11] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:11] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:21] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:21] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:21] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:21] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:21] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:21] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:31] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:31] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:31] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:31] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:31] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:31] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
Ce se intimpla, nu am imagine?
lipsa mgcamd ( alte emu parca nu pot lucra corect cu ecm TVR )
Salut,
Tot eu . Va rog, mai am nevoie de un pic de ajutor de la voi.
Cum stau acum: m-am folosit de sfaturile voastre si am un card focussat in interfata phoenix.
Normal http://sateliti.info/images/smilies/Comp_arunc.gif, nu reusesc sa vad vreun canal codat din grila focus. Nu mai zic nimic de sharing , eu vreau acum sa fac sa functioneaze cardul asta in phoenix. Mentionez ca in receptorul de la ei cardul este functional, deci nu e o problema cu el.
Am cules informatii despre ce si cum trebuie sa fac si:
-am instalat in receptor mbox ultima varianta, am pornit emu mbox+newcs, am pornit scriptul de serial+USB. Totul cum a descris snow in postul 14 de mai sus.
-am urcat cu ftp-ul fisierele postate de catre voi: (mbox.cfg, cwshare.cfg, add.data, 10110.list) in folderul var/keys si newcs.xml in folderul var/tuxbox/config. le-am setat la toate atibutul 755
-am instalat pe calculator mbox control center; am creat un profil, s-a conectat la receptor
Ce cred eu ca nu este in regula:
1.Motoru, spuneai intr-un post mai sus ca s-ar putea ca la cardul focussat sa difere frecventa cuartului. In newcs.xml postat de snow aceasta valoare este de 357. Ramane asa sau trebuie schimbata?
2.cand dau restart Mbox de la butonul din control center, in stanga jos scrie pasii pe care ii face. Se opreste cu eroare atunci cand se pare ca citeste mbox.cfg. Iata care este descrierea acestei erori:
===========
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
===========
3.In mbox control center are in meniu un tab numit "Newcs" si care deschide o forma ce iti ofera posibilitatea sa te conectezi, sau cel putin asa cred eu, la newcs. Ce setari trebuie in acele campuri?: IP-adress/DNS (eu am incercat si cu IP-ul receptorului(192.168.1.10) si cu 127.0.0.1 cel folosit, am vazut, in cwshare.cfg), Port(am incercat si cu 10110 si cu 14000), Password(am incercat si cu dummy si cu newcs si fara nimic). Mesajul dupa apasarea butonului "Connect" este invariabil acelasi: "Connection is forcefully rejected"
4.Din telnet la comanda mbox.sh40 iata ce se intampla:
=============
-sh-3.00# mbox.sh40
[12:21:04] STAPI INIT ... OK
[12:21:04] ExYuSAT Team http://www.exyusat.com , http://mbox.exyusat.com/index.php
[12:21:04] Starting MBOX version 0.4 BETA (build 0019) coded by The_Ripper
[12:21:04] This program is for educational & informational purposes only!!
[12:21:04] Donation to project: http://mbox.exyusat.com/donate.htm
[12:21:04] ===> Net Mode <===
[12:21:04] Reading cwshare.cfg ...
[12:21:04] Trying to get online,please wait ...
[12:21:04] Total 1 newcamd server(s) to connect
[12:21:04] Creating ecm parser thread ...OK
[12:21:04] Creating timer thread ...OK
[12:21:04] Creating newcamd worker thread ...OK
[12:21:04]
[12:21:04] ReReading pmt.tmp
[12:21:04] [newcamd] Trying to connect to newcamd server (127.0.0.1:10110)
[12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...
[12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).
[12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).
[12:21:05] [newcamd] Trying to connect to newcamd server (127.0.0.1:10110)
[12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...
[12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).
[12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).
=============
Nu stiu, pare ca se conecteaza la interfata(Connected to (127.0.0.1:10110)) dar gaseste serverul oprit(... or server gone offline)!!
Din experineta voastra, aveti idee unde este buba (sau bubele)?
Multumesc pentru orice sfat,
Rocco
"My goal is simple. It is a complete understanding of the universe, why it is as it is and why it exists at all." - Stephen Hawking
357 e bun pt focus, la ora aceea nu ma informasem suficient cu frecventele, e absolut corect ce a scris snow.
Daca ai facut tot ce scrie acolo trebuie sa mearga !
important:
- in mbox.cfg D { 2 }
- in cwshare.cfg introduci linia C: { 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 0B000000:0B000000;} si pui localul prioritar cu linia H: { 0B000000; }
-in 10110.list pui SF: { 0000 }
pt sharing(network mode) trebuie sa-ti pui linie M (host and pass)+hostIP+setare rooter, exista tutoriale pt asta.
daca nu te descurci iti trimit fis gata configurate.
Last edited by motoru; 07-11-08 at 22:32.
IPBOX 900 HD, dreambox 800HD, dreambox 500, VU+duo, gigablue800HD, Vu+Duo2
Salut,
Va rog, ma poate ajuta cineva?
Nu reusesc sa "pornesc" cardul f___ss_t din phoenix, nu vad niciun canal codat.
In plus de postul meu de mai sus am constatat ca:
-daca pornesc din telnet mbox.sh40, incepe sa scrie in debug.txt din folderul temp: Iata ce imi apare atunci cand browsez pe canalele codate:
[00:01:46] ReReading pmt.tmp
[00:01:46] ==================================================================
[00:01:46] ECM: CA ID: 0x0B00 Conax -> CA PID: 0x011F
[00:01:46] ==================================================================
[00:01:49]
[00:01:49] ReReading pmt.tmp
[00:01:49] ==================================================================
[00:01:49] ECM: CA ID: 0x0B00 Conax -> CA PID: 0x012F
[00:01:49] ==================================================================
Cele 2 PID-uri de mai sus corespund la TVR1 si TVR2.
Ce concluzii trag de aici:
-scriptul de serial-usb este instalat corect
-cardul se simte, ca nu i-am spus nicaieri ca e conax
-ceva, ceva tot face configurarea mea mbox+newcs. dar...
-ce e insa gresit? newcs.xml, mbox.cfg, cwsare.cfg sau 10110.list?
Alte intrebari?
-pentru card conax, cazul meu, in newcs.xml linia "<!-- <boxkey>0000000000</boxkey> -->" trebuie decomentata sau nu? Si daca da, ce trebuie in loc de "0000000000"?
-nu mi-e foarte clar ce versiune de mbox ruleaza pe receptorul meu. De unde vad aceasta informatie? Eu ce-am facut: am luat ultima versiune de mbox, am copiat fisierele prin ftp in var/bin si am rulat din telnet fisierul mbox.sh40. E bine sau nu?
Multumesc,
Rocco
"My goal is simple. It is a complete understanding of the universe, why it is as it is and why it exists at all." - Stephen Hawking
foloseste newcs.xml-ul de aici
vezi ca-n var keys trebuie sa mai ai si newcamd.list
spune-mi ce ai in 10110.list
Salut,
Eu acum sunt la job, diseara de abia astept sa pun in practica e ai spus.
Alte date:
-1. Undeva se pare ca mi-a scapat informatia cum ca ar fi trebuit si fiserul "newcamd.list". Asa e, nu il am, mersi ca ai observat. Am cautat acum pe forum si nu am gasit decat ceva mai vechi postat de otheitis:
#CWS_KEEPALIVE = 300
#CWS_INCOMING_PORT = 12000
CWS = 192.168.1.5 10110 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
CWS = 192.168.1.5 10111 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
#lan newcs
E bine?
-la mine, de fapt, IP-ul asta va fi 192.168.1.10
-textul abipbox e ok?
-2. newcs.xml atasat de tine acum difera de cel al meu(care este tot de la tine dintr-un post mai vechi) prin linia asta care e acum in plus: <autosid>no</autosid>. O sa-l modific in consecinta.
-3. 10110.list contine o singura linie, si anume:
SF: { 0000 }
Mersi mult snow,
rocco
"My goal is simple. It is a complete understanding of the universe, why it is as it is and why it exists at all." - Stephen Hawking
CWS = 127.0.0.1 10110 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
CWS = 127.0.0.1 10111 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
Asa sa il pui....Eu am folosit pe ip care am avut la ipbox atunci.Cu asta o sa merge 100%
orice ip si sa ai pe ipbox.
Salut,
Am facut toate setarile in toate fisierele asa cum m-ati indrumat.
Din pacate nu reusesc nicicum sa pornesc tot mecanismul asta mbox+newcs+phoenix, pur si simplu nu se deschide niciun canal codat.
Va rog, ca sa ma linistesc si eu, imi poate raspunde cineva la aceste 3 nelamuriri?
Folosesc MBOX control center. Tool-ul asta(care arata foarte bine, pacat ca nu are si un help) imi indica 3 posibile probleme, si anume:
-1. in tab-ul telnet la comanda mbox.sh40 dupa linia in care se comunica faptul ca s-a conecatat la device ([12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...) lucrurile nu mai sunt ok. Mesajele sunt ([12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).) si ([12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).). Am cautat pe net dar numai o singura pagina imi gaseste pe google(numai ca e ceva adiacent despre o altfel de problema). Altceva ce nu inteleg este daca acest server de newcs trebuie pornit in mod explicit de undeva sau nu.
-2. daca dau restart MBOX de la butonul dreapta sus, dupa ce trece prin pasii(ii scrie in fereastra aplicatiei in bara de dialog din stanga jos) de connect ok, kill ok, la citirea mbox.cfg procesul crapa: mesajul de eroare este nespecific "An invalid argument was supplied" - pare ca e din .net framework - si aplicatia se inchide.
-3. in tabul newcs exista, sau asa pare, o metoda de conectare la serverul newcs. Orice configurare am facut pe IP, port, parola mesajul a fost invariabil acelasi: "Connection is forcefully rejected".
Rugamintea mea este sa imi confirmati sau nu daca aceste 3 chestii se intampla si la voi. Si daca stiti vreo solutie pentru ele.
Multumesc mult pentru orice sugestie,
rocco
"My goal is simple. It is a complete understanding of the universe, why it is as it is and why it exists at all." - Stephen Hawking
Incearca sa pui fisierele prin conectare ftp in fiecare director asa cum ti-am trimis im email .